Fork&Crane lifting truck
Briefing
Ø Fork lifting capacity 13.5tons,
Ø Crane lifting capacity 72 ton*m
Ø Remote control of crane operation
Ø Crane 360 degree rotating
Ø Crane jib boom reach up to 17meter height.
Benefit
u Cost saving, using one truck to do two task with using fork or crane lifting;
u Reduce space, with one truck occupying space needed;
u Labor cost reduction by operator wage pay;
u One truck’s cost for fuel and maintenance
HNFC135-720 参数表 Parameter
POS | ITEM DESCRIPTION | UNIT | HNFC135-720 | |
Characteristics | 1.1 | 起重量/载荷Capacity | Q(t) | 13.5 |
1.2 | 载荷中心距Load center | c(mm) | 600 | |
1.3 | ||||
1.4 | 轴距 Wheel base | y(mm) | 3250 | |
Weight | 2.1 | 自重 Truck Weight | kg | 21950 |
2.2 | ||||
2.3 | ||||
Chassis | 3.1 | 轮胎规格，前 Tyre Specs.:Front | 10.00x20/16PR | |
3.2 | 轮胎规格，后 Tyre Specs.:Rear | 10.00x20/16PR | ||
3.3 | 车轮，数量前/后（×=驱动轮）Tyres Qty,front/rear (X-drive wheels) | 4×/2 | ||
3.4 | 轮距，前 Wheel tread:Front | b10(mm) | 1677 | |
3.5 | 轮距，后 Wheel tread:Rear | b11(mm) | 2013 | |
Dimension | 4.1 | 门架/货叉架前/后倾角Mast/carriage tilt angle(front/rear) | ° | 6°/12° |
4.2 | 整车高度 Mast height(fork lowering) | mm | 3200 | |
4.3 | 标准起升高度 Max. lifting height | h3(mm) | 3000 | |
4.4 | 作业时最大高度 Overall height(fork raised) | h4(mm) | 4600 | |
4.5 | 总长(含2000mm货叉) Overall length (with 2000mm forks) | l1(mm) | 7600 | |
4.6 | 货叉垂直前表面至车辆后端距离Fork front vertical surface to the rear end of the vehicle | l2(mm) | 5600 | |
4.7 | 总宽Overall Width | b1/b2(mm) | 2250 | |
4.8 | 货叉尺寸 Fork dimension | s/e/l(mm) | 90x180x2000 | |
4.9 | 货叉架宽度 Fork carriage width | b3(mm) | 2200 | |
4.10 | 门架下最小离地间隙 满载 Mast Min ground clearance (with load) | m1(mm) | 225 | |
4.11 | 支腿最小离地间隙 Outrigger min ground clearance(with load) | m2(mm) | 320 | |
4.12 | 最小转弯半径 Min.Turning radius | Wa(mm) | ||
Performance | 5.1 | 运行速度（满载/无载） Travel speed (with load/without load) | km/h | 23/26 |
5.2 | 最大起升速度（满载/无载） Max.lifting speed (with load/without load) | m/s | 310/340 | |
5.3 | 爬坡度（满载/无载） Gradeablity (with load/without load) | % | 20 | |
5.4 | 行车制动Driving brake | 钳盘式制动器 clamp disco brake | ||
Engine | 7.1 | 内燃机生产厂名称/型号 Engine brand/model | 玉柴YC6J150-T301 | |
7.2 | Power ISO 1585 | KW | 110 | |
7.3 | rpm | min-1 | 2200 | |
7.4 | 气缸 air cylinder | cm3 | 6 | |
Other | 8.1 | 行驶控制方式 Driving control method | 液力变矩器torque converter | |
Jib | 9.1 | 重量Weight | Kg | 7800 |
9.2 | 控制方式 Control | 无线遥控Remote control | ||
9.3 | 支腿控制方式 Outrigger Control | 手动下车阀控制 Manual landing valve control | ||
9.4 | 主支腿外伸两侧中心距 main Outrigger Longitudinal span | mm | 4319 | |
9.5 | 后支腿外伸离转盘中心距 Distance between extending rear outrigger to center of swing platform | mm | 1582 | |
9.6 | 附加支腿外伸两侧中心距 Distance between the center of additional extended outrigger at two sides | mm | 2270 | |
